/**
  @page USBH_HID  USB Host HID example
  
  @verbatim
  ******************** (C) COPYRIGHT 2012 STMicroelectronics *******************
  * @file    readme.txt 
  * @author  MCD Application Team
  * @version V2.1.0
  * @date    19-March-2012
  * @brief   Description of the USB Host HID example
  ******************************************************************************
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the Licens
  *   
  ******************************************************************************
   @endverbatim

   
@par Example Description 

This example provides a description of how to use the USB OTG host peripheral 
on the STM32F2xx, STM32F4xx and STM32F105/7 devices.

When an USB Device is attached to the Host port, the device is enumerated and checked
whether it can support HID device or not, if the attached device is HID one, when the user
press the B3 button, the mouse or the keyboard application is launched.

Moving the mouse will move the pointer in the display rectangle and if a button is pressed,
the corresponding rectangle will be highlighted in green
If a keyboard has been attached, the display show the following messages and the taped
characters are displayed in green on the display.

This example works:
  - in high speed (HS) when the STM322xG-EVAL or the STM324xG-EVAL board and the
    USB OTG HS peripheral are used
  - in full speed (FS) when the STM322xG-EVAL or the STM324xG-EVAL board and the
    USB OTG FS peripheral are used, or when using the STM3210C-EVAL board.

@note In the USB Host HID class, two layouts are defined in the usbh_hid_keybd.h file
      and could be used (Azerty and Querty)
        //#define QWERTY_KEYBOARD
        #define AZERTY_KEYBOARD
      The User can eventually add his own layout by editing the HID_KEYBRD_Key array
      in the usbh_hid_keybd.c file
    
  
@par Hardware and Software environment 

   - This example runs on STM32F105/7 Connectivity line, STM32F2xx and STM32F4xx devices.
  
   - This example has been tested with STM3210C-EVAL RevB (STM32F105/7 devices), 
     STM322xG-EVAL RevB (STM32F2xx) and STM324xG-EVAL RevB (STM32F4xx)    

  - STM3210C-EVAL Set-up 
    - use CN2 connector to connect the board to a PC host or USB device

  - STM322xG-EVAL Set-up
    - Use CN8 connector to connect the board to a PC host or USB device when using USB OTG FS peripheral.
    - Use CN9 connector to connect the board to a PC host or USB device when using USB OTG HS peripheral.

  - STM324xG-EVAL Set-up
    - Use CN8 connector to connect the board to a PC host when using USB OTG FS peripheral
    - Use CN9 connector to connect the board to a PC host when using USB OTG HS peripheral


@par How to use it ?

 + EWARM
    - Open the USBH_HID.eww workspace.
    - In the workspace toolbar select the project config:
     - STM322xG-EVAL_USBH-HS: to configure the project for STM32F2xx devices and use USB OTG HS peripheral
     - STM322xG-EVAL_USBH-FS: to configure the project for STM32F2xx devices and use USB OTG FS peripheral
     - STM324xG-EVAL_USBH-HS: to configure the project for STM32F4xx devices and use USB OTG HS peripheral
     - STM324xG-EVAL_USBH-FS: to configure the project for STM32F4xx devices and use USB OTG FS peripheral
     - STM3210C-EVAL_USBH-FS: to configure the project for STM32F105/7 devices  
    - Rebuild all files: Project->Rebuild all
    - Load project image: Project->Debug
    - Run program: Debug->Go(F5)

 + MDK-ARM
    - Open the USBH_HID.uvproj project
    - In the build toolbar select the project config:
     - STM322xG-EVAL_USBH-HS: to configure the project for STM32F2xx devices and use USB OTG HS peripheral
     - STM322xG-EVAL_USBH-FS: to configure the project for STM32F2xx devices and use USB OTG FS peripheral
     - STM324xG-EVAL_USBH-HS: to configure the project for STM32F4xx devices and use USB OTG HS peripheral
     - STM324xG-EVAL_USBH-FS: to configure the project for STM32F4xx devices and use USB OTG FS peripheral
     - STM3210C-EVAL_USBH-FS: to configure the project for STM32F105/7 devices
    - Rebuild all files: Project->Rebuild all target files
    - Load project image: Debug->Start/Stop Debug Session
    - Run program: Debug->Run (F5)    

 + RIDE
    - Open the USBH_HID.rprj project.
    - In the configuration toolbar(Project->properties) select the project config:
     - STM322xG-EVAL_USBH-HS: to configure the project for STM32F2xx devices and use USB OTG HS peripheral
     - STM322xG-EVAL_USBH-FS: to configure the project for STM32F2xx devices and use USB OTG FS peripheral
     - STM324xG-EVAL_USBH-HS: to configure the project for STM32F4xx devices and use USB OTG HS peripheral
     - STM324xG-EVAL_USBH-FS: to configure the project for STM32F4xx devices and use USB OTG FS peripheral
     - STM3210C-EVAL_USBH-FS: to configure the project for STM32F105/7 devices
    - Rebuild all files: Project->build project
    - Load project image: Debug->start(ctrl+D)
    - Run program: Debug->Run(ctrl+F9)

 + TASKING
    - Open TASKING toolchain.
    - Click on File->Import, select General->'Existing Projects into Workspace' 
      and then click "Next". 
    - Browse to  TASKING workspace directory and select the project: 
     - STM322xG-EVAL_USBH-HS: to configure the project for STM32F2xx devices and use USB OTG HS peripheral
     - STM322xG-EVAL_USBH-FS: to configure the project for STM32F2xx devices and use USB OTG FS peripheral
     - STM324xG-EVAL_USBH-HS: to configure the project for STM32F4xx devices and use USB OTG HS peripheral
     - STM324xG-EVAL_USBH-FS: to configure the project for STM32F4xx devices and use USB OTG FS peripheral
     - STM3210C-EVAL_USBH-FS: to configure the project for STM32F105/7 devices
    - Under Windows->Preferences->General->Workspace->Linked Resources, add 
      a variable path named "Cur_Path" which points to the folder containing
      "Libraries", "Project" and "Utilities" folders.
    - Rebuild all project files: Select the project in the "Project explorer" 
      window then click on Project->build project menu.
    - Run program: Select the project in the "Project explorer" window then click 
      Run->Debug (F11)

 + TrueSTUDIO
    - Open the TrueSTUDIO toolchain.
    - Click on File->Switch Workspace->Other and browse to TrueSTUDIO workspace 
      directory.
    - Click on File->Import, select General->'Existing Projects into Workspace' 
      and then click "Next". 
    - Browse to the TrueSTUDIO workspace directory and select the project:  
     - STM322xG-EVAL_USBH-HS: to configure the project for STM32F2xx devices and use USB OTG HS peripheral
     - STM322xG-EVAL_USBH-FS: to configure the project for STM32F2xx devices and use USB OTG FS peripheral
     - STM324xG-EVAL_USBH-HS: to configure the project for STM32F4xx devices and use USB OTG HS peripheral
     - STM324xG-EVAL_USBH-FS: to configure the project for STM32F4xx devices and use USB OTG FS peripheral
     - STM3210C-EVAL_USBH-FS: to configure the project for STM32F105/7 devices
    - Rebuild all project files: Select the project in the "Project explorer" 
      window then click on Project->build project menu.
    - Run program: Select the project in the "Project explorer" window then click 
      Run->Debug (F11)
    
@note Known Limitations
      This example retargets the C library printf() function to the EVAL boards LCD
      screen (C library I/O redirected to LCD) to display some Library and user debug
      messages. TrueSTUDIO Lite version does not support I/O redirection, and instead
      have do-nothing stubs compiled into the C runtime library. 
      As consequence, when using this toolchain no debug messages will be displayed
      on the LCD (only some control messages in green will be displayed in bottom of
      the LCD). To use printf() with TrueSTUDIO Professional version, just include the
      TrueSTUDIO Minimal System calls file "syscalls.c" provided within the toolchain.
      It contains additional code to support printf() redirection.
    
 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */
