ADM1069 Super Sequencer with Margining Control

The ADM1069 Super Sequencer® is a configurable supervisory/sequencing device that offers a single-chip solution for supply monitoring and sequencing in multiple supply systems. In addition to these functions, the ADM1069 integrates a 12-bit analog-todigital converter (ADC) and four 8-bit voltage output digital-toanalog converters (DACs). These circuits can implement a closedloop margining system that enables supply adjustment by altering either the feedback node or reference of a dc-to-dc converter using the DAC outputs.

For more information about the ADM1069 register map, refer to the AN-721 Application Note.

Applications

Features and Benefits
  • Complete supervisory and sequencing solution for up to 8 supplies
  • 8 supply fault detectors enable supervision of supplies to
  • <0.5% accuracy at all voltages at 25°C
  • <1.0% accuracy across all voltages and temperatures
  • 4 selectable input attenuators allow supervision of supplies to
  • 14.4 V on VH
  • 6 V on VP1 to VP3 (VPx)
  • 4 dual-function inputs, VX1 to VX4 (VXx)
  • High impedance input to supply fault detector with thresholds between 0.573 V and 1.375 V
  • General-purpose logic input
  • 8 programmable driver outputs, PDO1 to PDO8 (PDOx)
  • Open-collector with external pull-up
  • Push/pull output, driven to VDDCAP or VPx
  • Open-collector with weak pull-up to VDDCAP or VPx
  • Internally charge-pumped high drive for use with external N-FET (PDO1 to PDO6 only)
  • See data sheet for additional features
    • Power Management
    Data Sheets
    Documentnote
    ADM1069: Super Sequencer with Margining Control Data Sheet (Rev. E)PDF 787.32 K
    Application Notes
    Documentnote
    AN-1009: Block Erasing, Reading and Writing to the ADM106x EEPROM (Rev. A)PDF 63 kB
    AN-1086: Using an ADM106x in a Hot Swap Application (Rev. 0)PDF 59 kB
    AN-0997: Ping-Pong Configuration Guide for ADM1062 to ADM1069 Devices (Rev. A)PDF 172 kB
    AN-1001: Checksum Calculations (Rev. A)PDF 76 kB
    AN-897: ADC Readback Code (Rev. A)PDF 65 kB
    AN-0973: Erasing and Programming the Sequencing Engine EEPROM (Rev. A)PDF 61 kB
    AN-0975: Automatic Generation of State Diagrams for the ADM1062 to ADM1069 Using Graphviz (Rev. A)PDF 209 kB
    AN-722: Watchdog Detection Using the ADM106x (Rev. 0)PDF 179 kB
    AN-721: ADM1068/ADM1069/ADM1168/ADM1169 Configuration Registers (Rev. B)PDF 500 kB
    AN-781: Monitoring Additional Supplies with the ADM1062-ADM1069 Super Sequencers™ (Rev. 0)PDF 96 kB
    AN-780: Monitoring Negative Voltages with the ADM1062 to ADM1069 Super Sequencers (Rev. A)PDF 98 kB
    AN-723: Interrupt Generation Using the ADM106x (Rev. 0)PDF 262 kB
    User Guides
    Documentnote
    UG-404: USB-SDP-CABLEZ Serial Interface BoardPDF 536 kB
    Order Information
    Part NumberPackagePacking QtyTemp RangePrice 100-499Price 1000+RoHS
    ADM1069ACPZ Production40 ld LFCSP (6x6mm w/4.1mm pad)OTH 490-40 to 85C4.714.4Y
    ADM1069ACPZ-REEL Production40 ld LFCSP (6x6mm w/4.1mm pad)REEL 2500-40 to 85C04.4Y
    ADM1069ACPZ-REEL7 Production40 ld LFCSP (6x6mm w/4.1mm pad)REEL 750-40 to 85C04.4Y
    ADM1069ASTZ Production32 ld LQFP (7x7mm)OTH 250-40 to 85C4.714.4Y
    ADM1069ASTZ-REEL Obsolete32 ld LQFP (7x7mm)REEL 2000-40 to 85C00Y
    ADM1069ASTZ-REEL7 Production32 ld LQFP (7x7mm)REEL 500-40 to 85C04.4Y
    Evaluation Boards
    Part NumberDescriptionPriceRoHS
    EVAL-ADM1069LQEBZEvaluation board for device allowing user to configure the board to match their own configuration. The kit includes an LQFP socket. Multiple boards can be cascaded (cable included), allowing evaluation of multi-device systems.303.6Y
    SOCKET-ADM1069LFZOptional LFCSP Socket for ADM1069 and ADM1169. This can be used with the evaluation board if required.-1Y
    USB-SDP-CABLEZUSB to Serial I/O Interface. One is required and can support multiple eval kits.89Y
    Reference Materials
    ADM1069: Super Sequencer with Margining Control Data Sheet (Rev. E) adm1069
    AN-0973: 超级时序控制器的EEPROM擦除和编程 (Rev. A) adm1060
    AN-780: 利用ADM1062至ADM1069超级时序控制器监控负电压 (Rev. A) adm1064
    AN-1009: Block Erasing, Reading and Writing to the ADM106x EEPROM (Rev. A) adm1065
    AN-1009: ADM106x EEPROM的块擦除、块读取和块写入 (Rev. 0) adm1065
    AN-1086: ADM106x的热插拔应用 (Rev. 0) adm1064
    AN-1086: Using an ADM106x in a Hot Swap Application (Rev. 0) adm1064
    AN-0997: Ping-Pong Configuration Guide for ADM1062 to ADM1069 Devices (Rev. A) adm1064
    AN-0997: ADM1062至ADM1069的“乒乓”配置指南 (Rev. 0) adm1064
    AN-1001: Checksum Calculations (Rev. A) adm1064
    AN-1001: 校验和计算 (Rev. 0) adm1064
    AN-897: ADC回读代码 (Rev. A) adm1060
    AN-897: ADC Readback Code (Rev. A) adm1060
    AN-0973: Erasing and Programming the Sequencing Engine EEPROM (Rev. A) adm1060
    AN-0975: 利用Graphviz自动生成ADM1062至ADM1069的状态图 (Rev. A) adm1064
    AN-0975: Automatic Generation of State Diagrams for the ADM1062 to ADM1069 Using Graphviz (Rev. A) adm1064
    AN-722: Watchdog Detection Using the ADM106x (Rev. 0) adm1060
    AN-721: ADM1068/ADM1069/ADM1168/ADM1169 Configuration Registers (Rev. B) adm1068
    AN-721: ADM1068/ADM1069/ADM1168/ADM1169的配置寄存器 (Rev. A) adm1068
    AN-781: 利用ADM1062–ADM1069 Super SequencersTM超级时序控制器监控额外电源 (Rev. 0) adm1064
    AN-781: Monitoring Additional Supplies with the ADM1062-ADM1069 Super Sequencers™ (Rev. 0) adm1064
    AN-780: Monitoring Negative Voltages with the ADM1062 to ADM1069 Super Sequencers (Rev. A) adm1064
    AN-723: 利用ADM106x产生中断 (Rev. 0) adm1060
    AN-723: Interrupt Generation Using the ADM106x (Rev. 0) adm1060
    UG-404: USB-SDP-CABLEZ Serial Interface Board adm1064
    UG-049：ADM1062至ADM1169超级时序控制器软件 adm1064
    Supervisory Devices Complementary Parts Guide for Altera FPGAs adm690
    Supervisory Devices Complementary Parts Guide for Xilinx FPGAs adm690
    Power Supply Sequencing Bulletin (2007) adm1060
    Products 产品服务
    Manufacturers 生产厂家
    Sales 联系购买
    ©1993 - 2024 BDTIC