The PCA9703 is a low power 18 V tolerant SPI General Purpose Input (GPI) shift register designed to monitor the status of switch inputs. It generates an interrupt when one or more of the switch inputs change state but allows selected inputs to not generate interrupts using the interrupt masking feature. The input level is recognized as a HIGH when it is greater than 0.8 × VDD and as a LOW when it is less than 0.55 × VDD (minimum LOW threshold of 2.5 V at 5 V node). The PCA9703 can monitor up to 16 switch inputs.
The falling edge of the CS pin samples the input port status and clears the interrupt. When CS is LOW, the rising edge of the SCLK loads the shift register and shifts the value out of the shift register. The serial input is sampled on the falling edge of SCLK. The contents of the shift register are loaded into the interrupt mask register of the device on the rising edge of CS.
Each of the input ports has a 18 V breakdown ESD protection circuit, which dumps the ESD/overvoltage current to ground. When used with a series resistor (minimum 100 kΩ), the input can connect to a 12 V battery and support double battery, reverse battery, 27 V jump start and 40 V load dump conditions in automotive applications. Higher voltages can be tolerated on the inputs depending on the series resistor used to limit the input current.
The INT_EN pin is used to both enable the GPI pins and to enable the INT output pin to minimize battery drain in cyclically supplied pull-up or pull-down applications. The SDIN pull-down prevents floating nodes when the device is used in daisy-chain applications.
With both the high breakdown voltage and high ESD, this device is useful for both automotive (AEC-Q100 compliance available) and mobile applications.
Name/Description | Modified Date |
---|---|
18 V tolerant SPI 16-bit GPI with maskable INT (REV 4.0) PDF (297.0 kB) PCA9703 | 05 Sep 2014 |
Name/Description | Modified Date |
---|---|
I2C-bus specification and user manual (REV 6.0) PDF (1.4 MB) UM10204 | 28 Apr 2014 |
I2C-bus specification and user manual (REV 5.0) PDF (1.6 MB) UM10204_JA | 03 Apr 2013 |
I2C Demonstration Board 2005-1 Quick Start Guide (REV 1.0) PDF (261.0 kB) UM10206 | 13 Jun 2006 |
Name/Description | Modified Date |
---|---|
NXP® I2C-bus solutions 2014: Smart, simple solutions for the 12 most common design concerns (REV 1.0) PDF (3.5 MB) 75017540 | 01 Aug 2014 |
Name/Description | Modified Date |
---|---|
plastic thin shrink small outline package; 24 leads; body width 4.4 mm (REV 1.0) PDF (353.0 kB) SOT355-1 | 08 Feb 2016 |
Name/Description | Modified Date |
---|---|
TSSOP24; Reel pack; SMD, 13" Q1/T1 Standard product orientation Orderable part number ending ,118 or... (REV 4.1) PDF (227.0 kB) SOT355-1_118 | 15 Apr 2013 |
Name/Description | Modified Date |
---|---|
Footprint for wave soldering (REV 1.0) PDF (16.0 kB) SSOP-TSSOP-VSO-WAVE | 08 Oct 2009 |
Product | Status | Reset input pin | Package name | Package version | Operating Temperature (Cel) |
---|---|---|---|---|---|
PCA9703PW/Q900 | Active | ||||
PCA9703PW | Active | no | TSSOP24 | SOT355-1 | -40~125 |
Product ID | Package Description | Outline Version | Reflow/Wave Soldering | Packing | Product Status | Part NumberOrdering code(12NC) | Marking | Chemical Content | RoHS / Pb Free / RHF | LeadFree Conversion Date | EFR | IFR(FIT) | MTBF(hour) | MSL | MSL LF |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
PCA9703PW | SOT355-1 | SSOP-TSSOP-VSO-WAVE | Reel 13" Q1/T1 | Active | PCA9703PW,118 (9352 890 45118) | PCA9703PW | PCA9703PW | Always Pb-free | 0.0 | 2.0 | 5E8 | 1 | 1 | ||
Bulk Pack | Active | PCA9703PW,112 (9352 890 45112) | PCA9703PW | PCA9703PW | Always Pb-free | 0.0 | 2.0 | 5E8 | 1 | 1 | |||||
PCA9703PW/Q900 | SOT355-1 | SSOP-TSSOP-VSO-WAVE | Reel 13" Q1/T1 | Active | PCA9703PW/Q900,118 (9352 890 63118) | PCA9703PW | PCA9703PW/Q900 | Always Pb-free | 0.0 | 2.0 | 5E8 | 1 | 1 |