LC898113: Optical Image Stabilization (OIS) Controller & Driver
The LC898113-TBM-H and LC898113RA-WH (referred to collectively as the LC898113 in this data sheet) are devices integrating digital gyro interface, gyro filter, stepping motor control circuit, and motor driver functions needed to implement an image stabilization system using stepping motors. These functions make it possible to build a system using a minimal software program that enables the host microcontroller to turn image stabilization on and off, for example. The gyro filter coefficients may be set to any values by the host microcontroller, making it possible to build filter circuits optimized for the system. The LC898113 integrates a signal determination circuit for pan/tilt processing and a filter circuit, enabling implementation of a variety of processing in response to camera movements. The LC898113 integrates four saturation-drive H-bridge channels for stepping motor drive, and PWM drive with 1-2-phase control to 8W1-2-phase control is supported. Also integrated are a photo sensor drive circuit for control object position detection (for example, a CMOS sensor), a position determination circuit, and a circuit for moving to the optical center based on the results from the preceding circuits. Thus, the host microcontroller can specify detection start and the LC898113 will automatically move the control object to the initial position. Both SPI and I2C are supported as serial interfaces for communication with the host microcontroller. This allows the customer to choose based on the specifications of the host microcontroller. The I2C interface also supports a 1.8 V interface.
特性- Serial interfaceSPI (mode0, mode3)I2C (F/S mode)Selection with MODE0 pin
- Built in Gyro filter
- Digital Gyro SupportBuilt in Digital Gyro I/F for each manufacturer
- Stepping motor drive mode1-2 phaseW1-2 phase2W1-2 phase4W1-2 phase8W1-2 phase
- Stepping motor driver integrated in an MCPSaturation driven H bridge 4chBuilt in thermal protection circuitBuilt in low voltage malfunction prevention circuitBuilt in transistor for photo sensor driveTwo driver power supplies (VM : for motor, VCC : for others)
- Operation ClockClock generated from built in oscillation amplifierClock input directly from CLKIN pinSelection with MODE1 pin
- Power supply voltage (Typical voltage)Logic LSI : Pin 3.3V, Inside 1.8V (External supply required)Driver LSI : VM 5.0V, VCC 3.3V
| 优势- A minimal software program enables the host microcontroller to turn image stabilization on and off, for example.
- The gyro filter coefficients may be set to any values by the host microcontroller, making it possible to build filter circuits optimized for the system.
- The LC898113 integrates four saturation-drive H-bridge channels for stepping motor drive, and PWM drive with 1-2-phase control to 8W1-2-phase control is supported.
- The host microcontroller can specify detection start and the LC898113 will automatically move the control object to the initial position.
|
应用- Optical Image Stabilization (OIS) Camera Modules
| 终端产品 |
数据表 (1)
封装图纸 (1)
产品订购型号
| 产品 | 状况 | Compliance | 封装 | MSL* | 容器 | 预算价格 (1千个数量的单价） |
|---|
| LC898113-TBM-H | Active | Pb-free
Halide free | LFLGA-49 / FLGA-49 | 569AM | 4 | Tape and Reel | 2000 | $3.7439 |
订购产品技术参数
| Product | VM Min (V) | VM Max (V) | VCC Min (V) | VCC Max (V) | IO Max (A) | IO Peak Max (A) | Step Resolution | Control Type | Feedback Method | Current Sense | Regulator Output | Fault Detection | Flyback Protection | RDS(on) Typ (Ω) |
|---|
| LC898113-TBM-H | 2.5 | 5.5 | 2.7 | 3.6 | 0.4 | 0.6 | 1/128 | I2C | None | None | No | | Integrated Active | 1.2 |
