TUSB2036 用于 USB 具有可选串行 EEPROM 接口的 2/3 端口集线器
The TUSB2036 hub is a 3.3-V CMOS device that provides up to three downstream ports in compliance with the USB version 1.1 specification. Because this device is implemented with a digital state machine instead of a microcontroller, no firmware programming is required. Fully-compliant USB transceivers are integrated into the ASIC for all upstream and downstream ports. The downstream ports support both full-speed and low-speed devices by automatically setting the slew rate according to the speed of the device attached to the ports. The configuration of the BUSPWR terminal selects either the bus-powered or the self-powered mode. The introduction of the DP0 pullup resistor disable terminal, DP0PUR, makes it much easier to implement an on-board bus/self-power dynamic-switching circuitry.
|
TUSB2036 |
TUSB2046B |
TUSB2077A |
| Supply Voltage(s)(V) |
3.3 |
3.3 |
3.3 |
| Operating Temperature Range(C) |
0 to 70 |
-40 to 85,0 to 70 |
0 to 70 |
| Pin/Package |
32LQFP |
32LQFP, 32QFN |
48LQFP |
| USB Speed |
Full |
Full |
Full |
| Integrated MCU Architecture |
N/A |
N/A |
N/A |
TUSB2036 特性
- Fully Compliant With the USB Specification as a Full-Speed Hub: TID #30220242
- Integrated USB Transceivers
- 3.3-V Low Power ASIC Logic
- One Upstream Port and 2-3 Programmable Downstream Ports
- Total Number of Ports (2 or 3) Selected by Input Terminal
- Total Number of Permanently Connected Ports Is Selected by 2 Input Terminals
- Two Power Source Modes
- Self-Powered Mode
- Bus-Powered Mode
- All Downstream Ports Support Full-Speed and Low-Speed Operations
- Power Switching and Overcurrent Reporting Is Provided Per Port or Ganged
- Supports Suspend and Resume Operations
- Suspend Status Terminal Available for External Logic Power Down
- Supports Custom Vendor ID and Product ID With External Serial EEPROM
- 3-State EEPROM Interface Allows EEPROM Sharing
- Push-Pull Outputs for PWRON Eliminate the Need for External Pullup Resistors
- Noise Filtering on OVRCUR Provides Immunity to Voltage Spikes
- Supports 6 MHz Operation Through Crystal Input or 48 MHz Input Clock
- Output Terminal Available to Disable External Pullup Resister on DP0 for 3 ms After Reset or After Change on BUSPWR and Enable Easy Implementation of On-Board Bus/Self Power Dynamic Switching Circuitry
- Available in 32-Pin LQFP Package With a 0.8 mm Terminal Pitch (JEDEC - S-PQFP-G For Low-Profile Quad Flat Pack)
TUSB2036 芯片订购指南
| 器件 |
状态 |
温度 |
价格 |
封装 | 引脚 |
封装数量 | 封装载体 |
丝印标记 |
| TUSB2036VF |
ACTIVE |
0 to 70 |
1.40 | 1ku |
LQFP (VF) | 32 |
250 | JEDEC TRAY (10+1) |
|
| TUSB2036VFG4 |
ACTIVE |
0 to 70 |
1.40 | 1ku |
LQFP (VF) | 32 |
250 | JEDEC TRAY (10+1) |
|
| TUSB2036VFR |
ACTIVE |
0 to 70 |
1.15 | 1ku |
LQFP (VF) | 32 |
1000 | LARGE T&R |
|
| TUSB2036VFRG4 |
ACTIVE |
0 to 70 |
1.15 | 1ku |
LQFP (VF) | 32 |
1000 | LARGE T&R |
|
TUSB2036 质量与无铅数据
| 器件 |
环保计划* |
铅/焊球涂层 |
MSL 等级/回流焊峰 |
环保信息与无铅 (Pb-free) |
DPPM / MTBF / FIT 率 |
| TUSB2036VF |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TUSB2036VF |
TUSB2036VF |
| TUSB2036VFG4 |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TUSB2036VFG4 |
TUSB2036VFG4 |
| TUSB2036VFR |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TUSB2036VFR |
TUSB2036VFR |
| TUSB2036VFRG4 |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TUSB2036VFRG4 |
TUSB2036VFRG4 |
TUSB2036 应用技术支持与电子电路设计开发资源下载
- TUSB2036 数据资料 dataSheet 下载.PDF
- TI 德州仪器USB选型与价格 . xls
- 所选封装材料的热学和电学性质 (PDF 645 KB)
- 使用数字隔离器设计隔离式 I2C 总线接口 (zhct119.PDF, 339 KB)
- 高性能SERDES及其在CPRI 接口的应用分析 (zhca076.HTM, 8 KB)
- 1Q 2011 Issue Analog Applications Journal (slyt399.PDF, 964 KB)
- 接口选择指南 (Rev. D) (PDF 2994 KB)
- Signaling Rate vs. Distance for Differential Buffers (PDF 420 KB)
- Q1 2009 Issue Analog Applications Journal (slyt319.PDF, 1.39 MB)
- Isolated RS-485 Reference Design (PDF 80 KB)
- 无铅组件涂层的保存期评估 (PDF 1305 KB)
- Analog Signal Chain Guide (8.62 MB)
- Industrial Interface IC Solutions (101 KB)
TUSB2036 工具和软件
